ONU Stick

OXG-10GS XGS-PON SFP+ ONU Stick

Hot-pluggable XGS-PON ONU in a standard SFP+ module with SC/APC receptacle, for adding 10G symmetric PON access to existing gateways, switches, routers and backhaul equipment.

PON Interface
1 × XGS-PON, SC/APC receptacle
PON Standard
ITU-T G.9807.1, G.9807.2, G.987.2
Line Rate
9.953 Gb/s upstream / 9.953 Gb/s downstream
PON Wavelength
TX 1270 nm (1260–1280 nm), RX 1577 nm (1575–1580 nm)
Overview

XGS-PON SFP+ ONU Stick

OXG-10GS is an XGS-PON ONU in a standard SFP+ form factor that can replace the Ethernet SFP+ module in an existing gateway, switch, router or backhaul unit. It integrates the XGS-PON MAC and an OMCI stack, runs 9.953 Gb/s symmetric over a single fiber with an SC/APC receptacle, reaches 20 km on single-mode fiber and draws less than 3 W.

Key Features

What the OXG-10GS brings to your network

01

Drop-in SFP+ form factor

Hot-pluggable SFP+ module that replaces the Ethernet SFP+ in gateways, switches, routers, VDSL MDUs, G.fast DPUs or backhaul equipment.

02

Symmetric 10G XGS-PON

Single-fiber bidirectional link at 9.953 Gb/s upstream and downstream, compliant with ITU-T G.9807.1 and G.9807.2.

03

20 km reach

1270 nm DFB laser transmitter and high-sensitivity 1577 nm APD receiver support 20 km over single-mode fiber.

04

Full OMCI management

Integrated XGS-PON MAC and ITU-T G.988 OMCI stack (L2 MAC bridge, up to 64 bridges) for remote supervision, monitoring and maintenance.

05

Low power, two temperature grades

Under 3 W from a single 3.3 V supply, in commercial (0 to 70 °C) or industrial (-40 to 85 °C) case-temperature versions.

06

Timing and OAM for backhaul

Synchronous Ethernet, IEEE 1588v2 (ITU-T G.8275) and IEEE 802.1ag / ITU-T Y.1731 OAM with hardware delay and loss measurement.

Technical Data

Technical Specifications

ModelOXG-10GS
PON
PON Interface1 × XGS-PON, SC/APC receptacle
PON StandardITU-T G.9807.1, G.9807.2, G.987.2
Line Rate9.953 Gb/s upstream / 9.953 Gb/s downstream
PON WavelengthTX 1270 nm (1260–1280 nm), RX 1577 nm (1575–1580 nm)
Transmit Power+4 to +9 dBm (1270 nm DML DFB laser)
Receiver Sensitivity-29 dBm (APD); overload -9 dBm
Transmission Distance20 km over single-mode fiber
Interfaces
Form FactorSFP+, hot-pluggable
Host InterfaceCML data I/O; I²C serial ID and digital diagnostic monitoring
Software & Management
ManagementOMCI (ITU-T G.988), L2 MAC bridge, up to 64 bridges
PON Resources256 GEM/XGEM ports, 64 T-CONTs
SynchronizationSyncE, IEEE 1588v2 / ITU-T G.8275
Ethernet OAMIEEE 802.1ag, ITU-T Y.1731 (hardware delay/loss measurement)
Physical & Environmental
Power Supply3.3 V DC from host (3.13–3.47 V)
Power Consumption< 3 W
Operating TemperatureCase 0 to 70 °C (commercial) / -40 to 85 °C (industrial)
Humidity5% to 95% (operating)
ComplianceRoHS-6
Downloads

OXG-10GS documents & firmware

Datasheet 1

FAQ

Frequently asked questions

Answers about deploying, configuring and integrating the OXG-10GS.

Are ORFA ONUs compatible with major OLT brands?

Yes. Compliant with ITU-T G.984 and G.9807.1 standards, our ONUs use an optimized OMCI stack designed for plug-and-play interoperability with major OLT brands such as Huawei, ZTE, Nokia and FiberHome. Compatibility is confirmed for each OLT model and software version before deployment.

Can ORFA ONTs be managed remotely?

Yes. ORFA terminal devices support standard TR-069 / TR-369 (USP), OMCI and Web GUI management, enabling Zero-Touch Provisioning and remote management from the operator’s ACS or USP controller. Available features can vary by model, so please confirm the requirements for your project with our team.

Project Support

Build Your Next PON Product with ORFA

Discuss product configuration, OLT compatibility, custom hardware, firmware functions, ID design or private-label requirements with our team.